Rigging and main sheet position
Moderator: Moderator
- Michel
- Recognized Old Salt
- Posts: 993
- Joined: Thu Oct 07, 2010 6:25 pm
Re: Rigging and main sheet position
I was able to handle it but it was at least 100% heavier! I felt like reefing earlier than usual! 
Michel Boulet
Ex: "Mari-Bell" Sandpiper 565 (18.5367454 ft)
Now: "Papou" Tanzer 16 dinghy
Montreal
"Let the world say what it will"
~~_/)~~
Ex: "Mari-Bell" Sandpiper 565 (18.5367454 ft)
Now: "Papou" Tanzer 16 dinghy
Montreal
"Let the world say what it will"
~~_/)~~
-
lustyslogger
- Recognized Old Salt
- Posts: 952
- Joined: Tue Dec 20, 2011 7:45 am
Re: Rigging and main sheet position
I once had a Lugar Leeward 16 and it was rigged with the mainsheet off the stern as I said. I have found a photo of the set up. As you can see that leaves the entire cockpit free (on the Lugar the centerboard truck intruded but on the Sunbird the CB Truck is inside of the cuddy and completely out of the way.
You do not have the required permissions to view the files attached to this post.
-
Friends with SCAMPS
- Major Contributor
- Posts: 218
- Joined: Sun Oct 28, 2012 6:28 am
Re: Rigging and main sheet position
Yes, our mainsheet is run like Michel's diagram, except it starts at a becket above the port block instead of an eye on the transom. From what I understand this will change the forces a little because it pulls down from a different point.. like having a down haul at the end of your boom. Try it, you can always put it back.
- TitusTiger
- Regular Contributor
- Posts: 177
- Joined: Sat Jan 05, 2013 9:27 pm
Re: Rigging and main sheet position
Yes try it!!!
It has been raining here...a lot --- I say that because I haven't been sailing and need to get some wind under my wings, but I am tempted to try it as well, because I already have two cleats at the stern... I don't think it would be too hard to add a cam on one of them
but I need to push another penguin off the ice first to see if there are sharks in the water
It has been raining here...a lot --- I say that because I haven't been sailing and need to get some wind under my wings, but I am tempted to try it as well, because I already have two cleats at the stern... I don't think it would be too hard to add a cam on one of them
but I need to push another penguin off the ice first to see if there are sharks in the water
OnPace with Titus
Synergetic -- Paceship -12
-
lustyslogger
- Recognized Old Salt
- Posts: 952
- Joined: Tue Dec 20, 2011 7:45 am
Re: Rigging and main sheet position
TitusTiger wrote:Yes try it!!!
It has been raining here...a lot --- I say that because I haven't been sailing and need to get some wind under my wings, but I am tempted to try it as well, because I already have two cleats at the stern... I don't think it would be too hard to add a cam on one of them
but I need to push another penguin off the ice first to see if there are sharks in the water
Hey FYI
I just looked up the data on the Paceship 12 on Sailboat Data website. There at the bottom was a little blurb "Thanks to Titus Tiger for info etc etc" Cool
- TitusTiger
- Regular Contributor
- Posts: 177
- Joined: Sat Jan 05, 2013 9:27 pm
Re: Rigging and main sheet position
I got the info from www.paceship.org they had some Paceships listed, but not the Oakisland, so I gave the guy all the info I had found in my research, a lot from the Paceship site. I alsof found some info from the town where it was built...lustyslogger wrote:
Hey FYI
I just looked up the data on the Paceship 12 on Sailboat Data website. There at the bottom was a little blurb "Thanks to Titus Tiger for info etc etc" Cool
OnPace with Titus
Synergetic -- Paceship -12
-
lustyslogger
- Recognized Old Salt
- Posts: 952
- Joined: Tue Dec 20, 2011 7:45 am
Re: Rigging and main sheet position
I apologize for not being much of an artist but this is the way the Lugar Leeward 16 was rigging
You do not have the required permissions to view the files attached to this post.
- TitusTiger
- Regular Contributor
- Posts: 177
- Joined: Sat Jan 05, 2013 9:27 pm
Re: Rigging and main sheet position
I'm in the process of selling Lustys L picture on e-bay
OnPace with Titus
Synergetic -- Paceship -12
-
lustyslogger
- Recognized Old Salt
- Posts: 952
- Joined: Tue Dec 20, 2011 7:45 am
Re: Rigging and main sheet position
I may be the next Jackson Pollock!!TitusTiger wrote:I'm in the process of selling Lustys L picture on e-bay
- TitusTiger
- Regular Contributor
- Posts: 177
- Joined: Sat Jan 05, 2013 9:27 pm
Re: Rigging and main sheet position
looks more like Marcel Dusail
(joke on Duchamp)
(joke on Duchamp)
OnPace with Titus
Synergetic -- Paceship -12